how to reset mass air flow sensor bmw

Remove the two T20 Torx fasteners from the mass air flow sensor green arrows. The sensor itself is located near the air filter housing on the drivers side of the engine.

Signs That You Have A Failing Mass Air Flow Sensor Breakerlink Blog

Put your multimeter in Volts DC mode V and connect one probe of the multimeter to a good ground point on your car like the metal frame or engine block if you cant find any suitable metal parts use a plastic cover for instance.

. Disconnect mass air flow sensor harness connector. Start engine and warm it up to normal operating temperature. The Mass Air Flow MAF sensor is a really important component of your vehicles electronic fuel injection system.

The stored compensation factors are reset to 0 in the process. Intake manifold flap actuator. The mass air flow sensor or MAF sensor is part of the intake system in BMW X3 responsible for measuring the amount of air entering the engine.

Connect the mass air flow MAF sensor electrical connector. Figure 9 Working in the engine compartment loosen air flow meter clamp green arrow then disconnect the air duct from air flow meter by pulling straight off air flow meter. Code 3263 oxygen sensor.

The code for it was 0 928 400 529. When the battery is removed all MAF sensors will be reset in about 10 to 15minutes time. Just double checked on my BMW system hex code would be 3ff0 air-mass flow sensor.

Turn ignition switch OFF. Restart engine and let it idle for at least 5 seconds. Tighten the mounting screws to 27 in lb 3 Nm.

The most common signs of bad mass air flow sensor MAF in BMW X1 are loss of power or slow acceleration engine hesitation or jerking during acceleration erratic idling misfires poor exhaust emission values and sometimes black smoke comes out of the tailpipe. Remove the MAF sensor mounting screws. Ratio of calculated to measured air mass too high.

Disconnect the mass air flow MAF sensor electrical connector. OBD Code P0103 refers to. But if you let the car idle instead then the mass air flow sensor should reset.

Intake manifold flap actuator. We sell oem air mass sensors air flow meters and hfms hot film meter for many bmws. The MAF sensor is located between the intake manifold and the air filter of the engine of your vehicle.

How to Reset the Mass Air Flow Sensor. Position the MAF sensor on the throttle body. How To Reset Mass Air Flow Sensor Bmw - Is there any way to reset the light without going to the dealer.

Found in section DTC P0133 P0153 AF SENSOR 1 from page EC-265 5. The following learned values will return to the initial state. How do you reset a mass air flow sensor.

Restart engine and let it idle for at least 5 seconds. These guidelines apply to BMW E90 E91 E92 and E93 vehicles. Start engine and warm it up to normal operating temperature.

Connect the second probe of the multimeter to the black wire of the Mass Airflow Sensor. I always reset DME adaptations using BMW Scanner 14 or INPA and clear trouble codes after replacing parts that affect the fuel or air control such as MAF O2 sensors ICV throttle body etc. The mass air flow sensor is part of the engines intake system and is located.

I always got a 3ff0 which tell me that air flow meter sensor is bad. Let soak the lower section of your mass air flow sensor not the plug part in acetone or another solvent for a few minutes which will take out most of the grime. 4 Jan 13 2017 Edited Only show this user.

We sell oem air mass sensors air flow meters and hfms hot film meter. Then unclip the two spring clips green arrows that hold the mass air flow sensor. Intercooling of charge air.

Remove the sensor from the housing. Returning learned values of the intake system to the initial state. Unplug the electrical connector.

If stuck use a small flathead screwdriver to gently lever it out of the duct. This is just a matter of course and often may not be needed. CLEAR THE SELF-LEARNING DATA the manual SELF-LEARNING CONT procedure 1.

Disconnect mass air flow sensor harness connector. Remove the sensor from the intake air duct. Find the location of the MAF sensor in your X3 it will be somewhere between the air filter box and the throttle body.

The engine still drove like it was a bit breathless so I bit the bullet and bought a brand new MAF sensor. Disconnect mass air flow sensor harness connector. Cleaning dirty MAF sensor in BMW X3.

Resetting the Mass Air Flow Sensor by Idling the Engine Turn off the engine and let it cool down if youve been driving Remove the connector with the harness of the sensor Pull out the air flow sensor and clean it properly If you need to replace it with. Use q-tip or MAF cleaner soaked paper towel to gently clean exposed wire sensor. The mass airflow sensor is held in place with two screws and is very straightforward to replace.

Perform this coding also after removing the leak on the intake system. The PCM detects that the actual MAF sensor frequency signal is not within a predetermined range of the calculated MAF value for more than 40 seconds. Only show this user.

I bought a 2004 X3 recently and even though the Check Engine light was not on I did buy a can of Mass Air Flow sensor cleaner and cleaned the MAF. Install the MAF sensor mounting screws. Next disconnect air flow meter electrical connector by pressing wire clip purple arrow and pulling it straight off.

Stop engine and reconnect mass air flow sensor harness connector. A more technical description would be that the MAF circuit had higher than expected voltage air flow. In most modern vehicles there is an IAT sensor intake air temperature sensor.

BMW Diagnostics with ISTA - How to reset mass air flow MAF adaptation values with ISTA DThe information contained on this video are for educational and info. This guide provides instructions on how to change the Mass Air Flow MAF sensor on a 2004-2013 BMW 3-Series. Turn ignition switch OFF.

Install a new mass air flow sensor into the air filter housing. Basically this means that there is a problem with the Mass Air Flow High MAF sensor or circuit. Spray at least 10 spurts of MAF cleaner onto the sensor and then let it air.

It is installed in the MAF sensor. The transformation was remarkable - the engine seemed to pull with. Erase the DTC memory.

Remove the MAF sensor from the throttle body.

Pin On Auta